Banseok Dispensing Systems
Controllers, valves, pumps, robots, two-part and jetting systems, and complete in-line dispensing lines from Banseok Precision of Korea. Supplied and supported in Singapore by Blaze Technology.
Banseok Range at a Glance
Controllers, valves, tanks, pumps and ready-to-use dispensing sets supplied by Blaze Technology.
Product photos: Banseok Precision.
Dispensing Controllers
Air-pressure and timing controllers for barrels, valves and robots.
| Model | What it is | Key figures |
|---|---|---|
| TAD-200S / 200V | Microprocessor controller for barrels or valves | 0.01–99.99 s; vacuum suck-back |
| TAD-280L | Barrel / single-acting valve controller | 0.001–9.999 s; ±3% |
| TAD-300L | Time controller that adjusts for barrel level | 1–10 channels; 500 memories |
| TAD-2000S / TAD-5000S/V | Multi-channel controllers for robots and lines | 2 or 5 channels |
| TAD-400SR / SRT-M5 | Spray and air-blow controllers | 0.01–99.99 s; up to 5 channels |
| TAD-200SP | Dispensing plus vacuum pick-up | Pick-up pen included |
| EZ TEM-3 | Barrel heater controller | to 80 °C or 200 °C; 0.3% |
| BX-2 / BRP-3 | Rotary tubing dispensers | 0.01–20 ml/min; up to 300 cps |
Precision Valves
A valve for every material, from water-thin fluids to pastes.
| Model | What it is | Key figures |
|---|---|---|
| BV-M003 / M015 / M055 | Metering valves | 0.1–5.5 cc per shot; 10k–500k cps; ±1% |
| BV-M0250T | Metering valve for thin and anaerobic fluids | up to 0.25 cc; 1–5,000 cps |
| BV-175P-5M | Multi-nozzle metering valve | up to 8 nozzles; 0.1–2 ml each |
| BV-302 / 303 / 325 | Needle-off and suck-back valves | 1–200k cps; no drip |
| BV-386 / 396 / 3892 / 3893 | High-pressure, high-volume valves | up to 1,000,000 cps |
| BV-520M / 520P / 520PK | Precision needle valves | 0.8 L/min; PEEK version for anaerobics and UV |
| BV-500 / 500T | Spray valves; 500T for conformal coating | 1–1,000 cps |
| BV-300N | Diaphragm valve | 1–5,000 cps |
| BV-600C | Rotary valve for EMI silicone and rubber | 10k–600k cps |
| BV-T900 | Two-part suck-back valve with static mixer | paste viscosity |
Standard Systems, Tanks and Pumps
Feed the material from syringe, cartridge, tank, pail or drum.
| Model | What it is | Key figures |
|---|---|---|
| TAD-101 to TAD-105 | Ready dispensing sets: syringe, cartridge, tube, tank and can-pump | from 0.0001 cc |
| BFT / BST / BMT / BIT | Pressure tanks | 1–100 L |
| BAT / BAST / BAMT | Agitation tanks; BAMT with heating, vacuum degassing and 2-part mixing | 1–100 L |
| BSP-330S / 330D | Cartridge pressure pumps; 330D switches cartridges automatically | 10:1; 10k–600k cps |
| PCP series | Pail and drum pumps (1–5 kg, 20 L, 200 L) | 10:1 or 60:1; to 1,000k cps |
| BV-M10 / M60 / M250 | Precision metering pumps | 10 / 60 / 250 ml per stroke |
| Mono pump | Rotor-stator pump | 0.1–1.5 cc/rev; ±1% |
| BGP / PGP / GP series | Gear pumps for cartridges, tanks and pails | 0.3–9.6 cc/rev |
| BS-1 | Syringe pump | 25 µl–25 ml; ±1% |
Robots, Two-Part and Jetting
Automatic dispensing on the bench or in the line.
| Model | What it is | Key figures |
|---|---|---|
| EASYRO / EASYWIN | Servo dispensing robots | 300×300 to 400×600 mm; ±0.02 mm |
| ECORO / ECOWIN | Stepper dispensing robots | 200×200 to 300×500 mm; ±0.05 mm |
| anyCartesian | Large high-speed robots (331, 441, 552, 882) | up to 600×600 mm |
| Multi-tool heads | 1–5 heads for barrels, valves or tubes | 3-axis micro holders |
| TAD-233 / 233P / 244 / 433P | Two-liquid meter-mix systems | ratio 100:10 to 100:100; vacuum degassing |
| TAD-275 series / MMA-50M | Small 2-part metering and dual-cartridge units | down to 0.03 ml resolution |
| HV-2000 Fusion Jet | Diaphragm jetting valve and controller | up to 300 Hz; dots to 10 nl |
| Nano spray | Ultra-fine spray coating | 0.1–10 µm coating |
In-line Systems and Accessories
Complete lines built to order, and the parts you use every day.
Automatic lines for electronics and displays.
- PCB and underfill lines (EASYLINE-3000/4000)
- Jet underfill for BGA, CSP and flip-chip
- Camera-module holder attach and LED lens dispensing
- Display, mobile glass and solar-module sealing lines
Special machines built around your material.
- 1-part and 2-part downpacking from pails
- Solder paste downpacking
- Hot-melt and low-pressure moulding systems
- Booster pumps for solar module sealing
Everything that goes on the dispenser.
- Barrels 5, 10, 30 and 50 cc with pistons, caps and adapters
- Cartridge holders 170–1,000 cc and 330 ml holders
- Dual cartridges 1:1 to 1:10 with static mixers
To connect and control.
- Teflon and silicone tubing
- Air regulators 0–2, 0–4 and 0–10 kg/cm²
- Needle adapters, luer lock, flat and ceramic nozzles
- Hand and foot switches, barrel stands
Questions
Who is Banseok?
Banseok Precision Industry is a Korean maker of dispensing equipment, founded in 1996 in Seoul. Blaze Technology supplies and supports Banseok products in Singapore and the region.
What is a downpacking system?
Downpacking (syringe filling) transfers adhesive, sealant or paste from bulk pails into syringes or cartridges without trapping air. It costs less than buying pre-filled syringes and keeps the material consistent.
Which valve should I use?
It depends on the material and shot size. Metering valves give exact shot volumes for thick materials; needle-off and suck-back valves suit general dispensing without dripping; spray valves suit coatings; jet valves place very small dots without touching the part. Tell us the material and we will recommend one.
Can you handle two-part materials?
Yes. Banseok two-liquid dispensers meter, mix and dispense 2K materials, from cartridge units to systems with tanks, vacuum degassing and adjustable mix ratios.
Can a system be custom-made?
Yes. Banseok builds in-line and special-order systems, for example underfill, camera-module, display and solar-module lines, and custom downpacking for solder paste.
Need to dispense or fill a material?
Tell us the material, viscosity, shot size and output. We will recommend the right Banseok setup.